Mitsubishi FR-SF spindle drive manual. Uploaded by. Zeynel Ulusoy. USA- E* AC SPINDLE DRIV TROUBLESHOOTING, i A D V A N C E D AND . Hi Guys, I Replaced the power supply (SF-PW) on this spindle drive about 3 months ago and it was working fine for the last 3 months. For the. Mitsubishi vector Inverter Motor (SF-V5RU Series), English, , MB. FR -A/F/E/D SERIES TECHNICAL MANUAL, English,
|Published (Last):||23 February 2008|
|PDF File Size:||18.97 Mb|
|ePub File Size:||14.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
SF-CA card is defective. Data change during orientation stop state is valid from the next orienta- tion. Based on point c, move point b. Item Cause Check Remedy The orientation control o In the same manner as the o Readjust the orientation circuit is abnormally Item 1 of bcheck that control circuit by referenc- set or defective.
During acceleration, deceleration, or constant speed? Note The stop position is controlled by a bit contact signal OlH to 12H and is controlled by the follow- ing equation.
However, to return back to 2 the normal operation mode, make sure to set the CVHS to “0”.
How do I correct it? At the time, the fan case with the cooling fan can be dismounted.
I just was afraid that the spindle controller cr-sf have been in conflict with the NC control or spindle motor. Any way thank you again and your information is wnoderful and very helpful to me. Check an alarm of follows. When the equipment Spin- be set. NC screen standard setting: Thanks for all the info and help. The unit is 8.
Please notice your Alarm, Diag or Error ffeqrol you had when you send back the defective unit. An instantaneous power o In the same manner as the o See fr-ef alarm No. When all signals are turned off openthe stop position is at the reference stop position 0 deg.
Motion A – The base shut-off occurs in the controller, the main circuit COntaCtor is turned off, and the motor stops in the free-run state.
Mitsubishi FR-SF: Industrial Automation, Control | eBay
The external speed o Increase the value of the o Correctly set the value of reference is incorrect. For the setting values, see “Parameter list” provided with the controller. The power voltage is 0 Check the power voltage using 0 Adjust the related control out of the range. Cl – EO Parameter 4: Stay frsqrol with the rest of our community and get the latest on our CNC parts, Technical support, Technical tips, Automation news, Industry news, and get exclusive deal alerts or coupon code.
In stock 3 fe-sf – Usually ships in 3 business days. IJI c7-E I 2: Refurbished by Mitsubishi Electric Automation. The following printed o In the same manner as the o Readjust the spindle orien- circuit board is defec- Item 1 of b above, check tation control circuit by tive.
Remember, the decel side of the drive has more base transistors 12 maybe? When decreasing PGl, point a approaches point c. The dr-sf power imped- o Check that the alarm occurs dr-sf Replace the power supply ante is high.
Determines the direction of the spindle rotation for position loop motor command direction G Standard value 20 2nd deceleration point range PGl: An input signal from 0 Check each bit of the 0 Check the input signal where the sequencer is abnor- external signals 1 and 2 in bits are abnormal so that mal. Encoder Magnesensor The angle of the creep speed is set.
Mitsubishi AC Spindle Drive FREQROL-SF Maintenance Manual
Last, insert your fingers into the hinge panel cavi- ties 2 positions and remove the entire SF-CA card from the hinge panel. Ln EMG, in-positior encoder output is not held. The equipment malfunc- D Check the signal waveforms o Correctly connect the ground tions by noise which at check pins CHCH9 or wires of the power supply, enters a signal from AGA for phase A signal and amplifier, and motor. If it frerol to be run with transistors not firing properly it will eventually take out the first transistor to fire after the transistor that wasn’t working.
The Ki magnification should be set to the magnification for VKI. Parameter Description Setting range unit dr-sf Control type such as gain during orien- tation stop is set. See each listing for international shipping options and costs. CCW Mckor forward rotation 1: Do not press this switch while the motor rotates.