This British Standard is the official English language version of. EN Together wi th BS EN i t supersedes. BS EN l which. BS EN BRITISH STANDARDOffshore containers and associated lifting sets — Part 1: Offshore containers — Design, manufacture. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European.
|Published (Last):||21 September 2009|
|PDF File Size:||16.11 Mb|
|ePub File Size:||11.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
B the lifting force is transferred through the thickness of a plate, plates with specified through thickness properties in accordance with EN shall be used. The inspection schedule shall be as laid down in Ideally, dynamic calculations or tests should be carried out to verify the ability of a container to withstand such loads. NOTE Consideration should be given to strength, durability, suitability, and possible hazards caused by 120799-1 of these materials.
Auslegung, Herstellung und Kennzeichnung. In addition, certificates of examination and tests shall be issued as described in NOTE 2 It is recommended that pad-eyes be slotted into the primary structure NOTE 3 Where ISO-corner fittings are mounted in conjunction with pad eyes, the corner ns are not intended for lifting with slings offshore. Containers, Certificates of conformity, Bulk storage containers, Marking, Test methods, Identification methods, Aluminium alloys, Steels, Structural design, Certification approvalLoading, Strength of materials, Welded joints, Weight massContainerization, Materials handling, Lifting, Offshore construction works, Freight containers, Inspection, Marine transport.
In addition to the pad eyes for the lifting set, these containers may have side mounted lugs suitable for use with the lifting equipment mounted on a skip lift vehicle. When materials of different galvanic potential are joined together, 10279-1 design shall be such that galvanic corrosion is avoided.
Only materials with non-ageing properties shall be used. Test temperatures and test results shall comply with the requirements given in 6.
BS EN 12079-1:2006
ENApproval testing of welders — Fusion welding — Part 2: Where design requirements are based on the gravitational forces derived from these values, those 12709-1 are indicated thus: For details of these and other benefits contact Membership Administration. For dated references, subsequent amendments to or revisions of enn of these publications apply to this European Standard only when incorporated in it by amendment or revision.
Ensure use of the most current version of this document by searching British Standards Online at bsonline. 120791- openings should be dimensioned and positioned so as to 13 EN In order to avoid building prototypes that will not pass the test, the ability of an open top container to withstand the load occurring in the 2-point lifting test should be checked by a suitable calculation method.
Only the primary structure shall be considered in the design calculations; however, on certain types of containers, e. No significant permanent damage shall occur. In addition to the pad eyes for the lifting set, these containers may have side mounted lugs suitable for use with the lifting equipment mounted on a skip lift vehicle.
Aluminium alloys and tempers specified in Tables 4 and 5 may be used.
Full text of “Safety British Standards”
This will allow for changes in 120779-1 amount and mass of equipment fitted in a container during its operational life, and it may also be useful to be able to carry a certain amount of non-permanent equipment.
Doors shall be capable of being secured in the open position. Welds between essential non-redundant and non essential primary structures shall be examined as for non-essential primary structures.
When materials of different galvanic potential are joined together, the design shall be such that galvanic corrosion is avoided. ENHot-rolled products in weldable fine grain structural steels — Part 1: Various BSI electronic information services are also available which give details on all its products and services. It recommends that new offshore containers be approved, prototype tested and certified by duly authorized bodies.
NOTE 2 The bottom face of the pocket may be fully closed but it is recommended that openings be provided to facilitate maintenance and to minimize 1079-1 risk of loose items being retained in the pockets which could subsequently fall out during 12097-1 operations.
The force shall be considered to be evenly distributed between n – 1 pad eyes where n is the actual number of pad eyes. If these details are to be used 12079–1 any other purpose than implementation then the prior BSIwritten permission of BSI must be obtained. In this case the inspection plate should be replaced clause 10 1279-1 the certificate of conformity revised clause NOTE 3 For containers with special features where additional design requirements apply, suitable tests should be made to verify that those requirements are met.
Each container shall have its own fabrication number. NOTE 1 Should a load cell be overloaded or receive a shock load e. See informative Annex for guidance.
Low alloy special steels. The container shall not be used until it is repaired and inspected by an inspection body. Other NDE methods shall be chosen with due regard to the conditions influencing the sensitivity of the methods. The test masses shall normally be evenly distributed inside the container.