Find the most up-to-date version of ASTM C at Engineering ASTM C pdf – Download as PDF File .pdf), Text File .txt) or read online. ASTM C Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile (External Load Crushing Strength). Lab ID: Use To determine first-crack.

Author: Akijind Kajigar
Country: Malta
Language: English (Spanish)
Genre: Environment
Published (Last): 21 June 2011
Pages: 162
PDF File Size: 7.53 Mb
ePub File Size: 7.17 Mb
ISBN: 881-9-52382-384-2
Downloads: 61708
Price: Free* [*Free Regsitration Required]
Uploader: Tekasa

The width of the? Originally approved in Test Method A is the standard test and referee and will require 3 to 6 days to complete. These tests are performed to establish whether or not the installed step has sufficient strength to withstand the speci? The blocking or restraints shall c4977 designed to avoid bene? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Additional timber blocks or similar supports are necessary to elevate the test pipes. Make an index mark on the gasket c4997 with the?

ASTM C – 18 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile

There shall be no visible leakage. A surfactant shall be added to the water to minimize air bubbles from clinging to the gasket material. This standard is subject to c97 at any time by the responsible technical committee and must be reviewed every? Therefore, results of two properly conducted tests by the same operator on the same material should not differ by more than 0. If a frame or riser has been designed to be? The shear strength limit shall be noted by a sudden reduction in the applied load or shearing of the concrete.


The machines used for performing the three-edge-bearing tests shall be veri?

Statements will be included zstm each when the proper data have been obtained and analyzed. In cases of disagreement arising from differences in values reported by the owner and the manufacturer when using this test method for acceptance testing, the statistical bias, if any, between the laboratory of the owner and the laboratory of the manufacturer should be determined with each comparison being based on testing specimens randomly drawn from one pipe of the type being evaluated.

Cylinder specimens of sizes other than 6 by 12 in. Next, immerse the gasket completely in water and measure the mass of the gasket while totally submerged.

The attachments to the rung are to be 31? Tighter joints will resist greater? At the end of the 3-h boiling period, turn off the heat and cool the specimen for a period of 3 h by running cold tap water into the boiler, or by placing the specimen in a separate container of water.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Current edition approved Oct. The rigid base shall be at least 6 in.

Wooden strips shall be straight, have a cross section of not less than 2 in. Run two tests on each core sample. The test specimen is? Before making the compression test, cap the ends of the specimen in order to meet the requirements of Practice C It shall be fastened to a steel or wood-faced steel beam of such dimensions that de?


ASTM C497 – 18

If the ratio of length to diameter is less than two, make allowance for the ratio of length to diameter by multiplying the compressive strength by the applicable correction factor given in the following table determine values not given in the table by interpolation: Weigh specimens weighing more than 1 kg to an accuracy of 1 g.

Link to Active This link will always route to the current Active version of the standard. Cylinder Strength Test Method The total force on the joint is the sum of the resultants of the pipe weight, the water weight, and the force applied by the test machine see Fig. Manhole Step Test Methods Gasket Lubricant Tests Warning—Block or restrain the test pipe assembly horizontally to prevent any inadvertent pipe movements. Aside from the procedures, this standard also details the significance and use of and the required test apparatus for each test.

A calibration curve shall be used. Next, slowly add 40 millilitres of standard 1-Normal hydrochloric acid, HCl, to the sample and water. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.